best high end speaker system image
lowest pri
I realize home speakers have an impeadance of 8 ohms and car speakers are usually 4 ohms. I was just curious if it would work; because I have some Yamaha home speakers that have busted cabinets. I have a nice home theater system and have no home use for these speakers but I could really use some high end in my car. These speakers of course have built in crossovers in each cabinet. Any advice would be helpful, except "go buy some 4 ohm tweeters", I am in nursing school so money is too tight for that. Thanks.
Answer
Keep in mind that you're adding load to your head unit which may cause it to get hotter....
http://spkrbox1.spaces.msn.com/ for real "sound" advice.
Your system won't mean squat without a well designed box to put your subs in. Some manufacturers have recommendations as to dimensions of various types of boxes. It is best to find someone who builds boxes if you go with something other than a sealed box.
You should always match up RMS (Root Mean Square) watts of Subs and amp per channel as well as impedance's(resistances). When a sub has rating of 600 Watts MAX it really has an RMS rating of about 200 Watts RMS. RMS is the nominal wattage your most likely going to get out of it. Remember, a 200 Watts RMS amplifier has more power output than a 200 Watt MAX.
If your amp is rated at 4Ω don't subject it to 2Ω, it will fry.
Here is the formula for subs in parallel:
Z = 1 / (1/sub1 + 1/sub2 + 1/sub3 + ....)
For series, just add them up (sub1 + sub2 + ...).
You can mix and match these equations to get the right impedance required by your amp.
Example 1: Amp is 2 channel and rated at 4Ω, 4 subs @ 4Ω each. If I connect two in parallel and the other two in parallel and connect the two pairs in series, I would have a total impedance(resistance) of 4Ω. So to the amp, it's just one sub.
Example 2: Amp is rated at 1Ω mono, 2 subs @ 4Ω each dual voice coil. If I connect two voice coils in parallel and the other two voice coils in series and connect the two subs in parallel, I would have a total impedance of 1.6Ω. Which would be perfect for a 1Ω stable mono amp.
You should use a capacitor as well.
Recommend for every 500 watts MAX you use a .5 Farad cap
Example: 1000 watts MAX - 1 Farad cap
You will also need what's called a "line level converter" if your stock head unit doesn't have RCA outputs or your amp doesn't have high-level inputs.
Try http://www.soundomain.com/shop you can find some really good deals, and this site is manufacturer certified. VERY IMPORTANT WHEN SHOPPING ON-LINE!!!
If you like I can send you some plans for reference. My plans are for a 4-th order band-pass bass box (A.K.A. bass-reflex) that holds two 12's.
Also included are java calculators you can use to figure parallel and series values given Ω values, tips on box building and types, calculating port diameter and length(if used), calculating box dimensions for types of boxes (sealed, wedge, cylindrical, etc.), materials needed and even how to make a jig for cutting perfect holes for your subs.
Just e-mail me sparky3489@yahoo.com
My system
Blaupunkt TSw1200 subs with a Sony XplÅd XM2200GTX.
My amp is 1200 watts (200 Watts RMS X 2), subs are 600 watts (200 Watts RMS) each, cap is 1.5 Farad
SPL is about 112 db each sub
Total cost(so far) = $410
Keep in mind that you're adding load to your head unit which may cause it to get hotter....
http://spkrbox1.spaces.msn.com/ for real "sound" advice.
Your system won't mean squat without a well designed box to put your subs in. Some manufacturers have recommendations as to dimensions of various types of boxes. It is best to find someone who builds boxes if you go with something other than a sealed box.
You should always match up RMS (Root Mean Square) watts of Subs and amp per channel as well as impedance's(resistances). When a sub has rating of 600 Watts MAX it really has an RMS rating of about 200 Watts RMS. RMS is the nominal wattage your most likely going to get out of it. Remember, a 200 Watts RMS amplifier has more power output than a 200 Watt MAX.
If your amp is rated at 4Ω don't subject it to 2Ω, it will fry.
Here is the formula for subs in parallel:
Z = 1 / (1/sub1 + 1/sub2 + 1/sub3 + ....)
For series, just add them up (sub1 + sub2 + ...).
You can mix and match these equations to get the right impedance required by your amp.
Example 1: Amp is 2 channel and rated at 4Ω, 4 subs @ 4Ω each. If I connect two in parallel and the other two in parallel and connect the two pairs in series, I would have a total impedance(resistance) of 4Ω. So to the amp, it's just one sub.
Example 2: Amp is rated at 1Ω mono, 2 subs @ 4Ω each dual voice coil. If I connect two voice coils in parallel and the other two voice coils in series and connect the two subs in parallel, I would have a total impedance of 1.6Ω. Which would be perfect for a 1Ω stable mono amp.
You should use a capacitor as well.
Recommend for every 500 watts MAX you use a .5 Farad cap
Example: 1000 watts MAX - 1 Farad cap
You will also need what's called a "line level converter" if your stock head unit doesn't have RCA outputs or your amp doesn't have high-level inputs.
Try http://www.soundomain.com/shop you can find some really good deals, and this site is manufacturer certified. VERY IMPORTANT WHEN SHOPPING ON-LINE!!!
If you like I can send you some plans for reference. My plans are for a 4-th order band-pass bass box (A.K.A. bass-reflex) that holds two 12's.
Also included are java calculators you can use to figure parallel and series values given Ω values, tips on box building and types, calculating port diameter and length(if used), calculating box dimensions for types of boxes (sealed, wedge, cylindrical, etc.), materials needed and even how to make a jig for cutting perfect holes for your subs.
Just e-mail me sparky3489@yahoo.com
My system
Blaupunkt TSw1200 subs with a Sony XplÅd XM2200GTX.
My amp is 1200 watts (200 Watts RMS X 2), subs are 600 watts (200 Watts RMS) each, cap is 1.5 Farad
SPL is about 112 db each sub
Total cost(so far) = $410
Where to get mini speaker & tweeter drivers?
Spyder
Many computer speakers and portable speakers 2-3" drivers. Where the heck can I get high-end mini drivers, and amplifiers, similar to the ones that Bose use in their portable/computer speaker systems
Answer
From Victoria's Secret!! They also deal in leather speaker skirts!!Heheh!!!!!!!!!
From Victoria's Secret!! They also deal in leather speaker skirts!!Heheh!!!!!!!!!
Powered by Yahoo! Answers
Title Post: Is it possible to place a tweeter from a home stereo speaker in a car?
Rating: 98% based on 989 ratings. 5 user reviews.
Author: Yukie
Thanks For Coming To My Blog
Rating: 98% based on 989 ratings. 5 user reviews.
Author: Yukie
Thanks For Coming To My Blog
Posts
No comments:
Post a Comment